Manufacturing Maintenance Specialist, TCC (MM21) Technical Certificate of Credit
Length of Program: Three (3) Semesters
Entrance Date: Beginning of each semester.
Entrance Requirements: Refer to Admissions criteria. Click for Entrance Score Requirements.
Age: Applicant must be 16 years of age or older.
Education: An applicant must be a high school graduate or the equivalent (GED). College transcripts will be evaluated on an individual basis.
Advisor: A Program Advisor should be consulted prior to enrolling in any course. An advisor will be assigned by admissions.
Program Final Exit Point: Manufacturing Maintenance Specialist, Technical Certificate of Credit.
Credits Required for Graduation: 32 Minimum semester hour credits required.
|1: Occupational Courses||32|
|IDFC 1011Direct Current I
Pre/Co-requisite(s): Provisional Admission Introduces direct current (DC) concepts and applications. Topics include: electrical principles and laws; batteries; DC test equipment; series, parallel, and simple combination circuits; and laboratory procedures and safety practices.
|IDSY 1190Fluid Power Systems
This course provides instruction in the fundamentals of safely operating hydraulic, pneumatic, and pump and piping systems. Theory and practical application concepts are discussed. Topics include hydraulic system principles and components, pneumatic system principles and components, and the installation, maintenance, and troubleshooting of pump and piping systems.
Introduces electrical symbols and their use in construction blueprints, electrical schematics, and diagrams. Topics include: electrical symbols, component identification, print reading and scales and measurement.
|ELTR 1110Electric Motors
Introduces the fundamental theories and applications of single-phase motors. Topics include: motor theory/operating principles, motor terminology, motor identification, NEMA standards, motor efficiencies, preventive maintenance, troubleshooting/failure analysis, and NEC requirements.
|ELTR 1120Variable Speed/Low Volt Ctrls
Introduces types of electric motor control, reduced voltage starting, and applications. Emphasis will be placed on motor types, controller types, and applications. Includes information on wye and delta motor connections; part wind, autotransformer; adjustable frequency drives and other applications; and oscilloscopes and their operation. Topics include: types of reduced voltage starting, reduced voltage motor connections, and adjustable frequency drive.
|ELTR 1180Electrical Controls
Introduces line and low voltage switching circuits, manual and automatic controls and devices, and circuits. Emphasis will be placed on switching circuits, manual and automatic controls and devices, line and low voltage switching circuits, and operation, application and ladder diagrams. Topics include: ladder and wire diagrams, switching circuits, manual controls and devices, automatic controls and devices, and application and operation of controllers and controls.
|ELTR 1220Industrial PLC's
Introduces operational theory, systems terminology, PLC installations, and programming procedures for programmable logic controls. Emphasis is placed on pic programming, connections, installations, and start-up procedures. Topics include: PLC hardware and software, PLC functions and terminology, introductory numbering systems, PLC installation and set up, PLC programming basics, relay logic instructions, timers and counters, connecting field devices to I/O cards, and PLC safety procedures.
|ELTR 1250Diagnostic Troubleshooting
Introduces diagnostic techniques related to electrical malfunctions. Special attention is given to use of safety precautions during troubleshooting. Topics include: problem diagnosis, advanced schematics, and sequential troubleshooting procedures.
|ELTR 1270NEC Industrial Wiring Applicat
Provides instruction in industrial wiring applications of the National Electrical Code. Topics include: rigid/IMC conduit installation, EMT conduit installation, busways installation, cable tray/wireway installation, and equipment installation (600 volts or less).
|WELD 1330Metal Welding and Cutting Tech
Pre-requisite(s): None This course provides instruction in the fundamentals of metal welding and cutting techniques. Instruction is provided in safety and health practices, metal fabrication preparation, and metal fabrication procedures.
Up one level
Programs of Study
Notice and Responsibilities Regarding this Catalog
The information in this College Catalog and Student Handbook accurately reflects current policies and procedures at the time of publication. Students are admitted to the College under and are subject to the provisions of the SRTC Catalog and Student Handbooks for the term they initially enroll. Students in all programs are admitted under and are subject to the provisions of the College Catalog and Student Handbook and applicable addendums for the term they are admitted to the program at Southern Regional Technical College. If for any reason, a break in enrollment occurs, students must reapply and satisfy the College Catalog and Student Handbook requirements for the term of their re-entry to any program. The provisions of this catalog are not to be regarded as an irrevocable contract between Southern Regional Technical College and the student. The College reserves the right to change any provision or requirement at any time.
Southern Regional Technical College. (2019). 2019-2020 College Catalog and Student Handbook
15689 US Highway 19 North • Thomasville, Georgia